Power System Analysis and Calculations In Electrical Networks Using Etap Power Station

Overview:

Power system equipment must withstand not only the rated voltage, which corresponds to the highest voltage of a particular system, but also expected short level. Accordingly, it is necessary to set protective relays based on these results obtained from short circuit study. One of hot issues now related to these is arc flashing study which is mainly based on the studies of short circuit and relay co-ordination as well. All these three issues should be dealt as integral parts & bulk.

Power System Analysis means verifying the adequacy of the power distribution system and its components recognize coordination related disturbances and outages and collecting the required data to perform a detailed required study.
The continuity and quality of electricity delivered safely and economically by today’s and futures electrical power networks are important for both developed and developing economies. The correct modeling of power system equipment and correct fault analysis of electrical networks are pre-requisite to ensuring safety and they play a critical role in the identification of economic network investments. Environmental and economic factors require engineers to maximize the use of existing assets which in turn require accurate modeling and analysis techniques

objective:

On successful completion of this course, participants will be able to:

• Exploring the powerful capabilities of ETAP Power Station from OTI.
• Understand importance of power system modeling
• Understand the need for calculation the short circuit current.
• Manual calculation of short circuit using simple methods like MVA method, P.U. system, etc

Who Should attend:

This course is intended for anyone who must perform calculations, provide settings or approve the work performed by others. The trainee should be a graduate engineer or have the equivalent practical work experience in electrical power systems. i.e.

• • Consulting Engineers.
  • Electrical Engineers.
  • Project Engineers.
  • Maintenance Engineers.
  • Commissioning & testing Engineers.

Training Methodology

The course is designed to maximize delegate benefit from the outset. The goals of each participant are discussed to ensure their needs are fulfilled as far as possible. Questions are encouraged throughout particularly at the daily wrap up sessions. This provides opportunities for participants to discuss specific issues and if possible find appropriate solutions. Case studies are employed to highlight particular points and appropriate video materials used to illustrate particular conditions.
Understanding system design and limitations is fundamental to ensuring adequate design & specification activities are undertaken.
Moreover, some simulations will be utilized during course sessions using world trade available software’s (ETAP power station

Out Lines:

• • Overview of ETAP Capabilities & Limitations.
  • One-Line Diagram/One line View (OLV).
  • Creating & Merging different revisions, presentations & configuration
  • Scenario, Study & Project Wizards.
  • Crystal Reports & Customizations.
  • AC & DC Element Descriptions.
  • Load modeling.
  • Add, updating and remove from ETAP library.
  • Electrical systems modeling and fundamentals.
  • Load flow (balanced & unbalanced) analysis.
  • Load Flow & Cable sizing.
  • Transformer sizing.
  • Benefits of calculated short circuit currents.
  • Introduction to Fault current Calculations in brief.
  • Breaking & making currents.
  • Per unit systems.
  • Different typical values of positive, negative & zero phase sequence impedances for unbalance faults.
  • Manual Calculations of Isc by MVA Method.
  • Calculation of Isc by Impedance method.
  • Calculation of Isc by symmetrical components.
  • Calculations as defined & recommended by IEC/ANSI standards.
  • Short Circuit Studies (Fault-Levels

—————————————————————————————————————–

Investasi dan Fasilitas

• Harga : (dilampirkan dalam Brosur penawaran)
• Fasilitas : Certificate, Training kits, USB 8 GB, Lunch, Coffe Break, Souvenir, City Tour
• Untuk peserta luar kota disediakan transportasi antar-jemput dari Bandara/Stasiun ke Hotel (berlaku bagi perusahaan yang mengirimkan minimal 2 peserta)
• Quota minimum Running 2 peserta (jogja, Solo, Semarang) Quota minimum Running 3 peserta ( Jakarta & Bandung) –  ( Untuk Manado, Bali , Balikpapan dan Lombok Quota minimal 4 peserta)

Tempat (Tentative):

• Hotel Santika Kuta, Bali
• Hotel Nagoya Plaza, Batam
• Hotel Fave, Balikpapan
• Hotel Aston, Manado
• The Santosa Villas and Resort, Lombok
• Hotel Gino Ferucci, Bandung
• Hotel Santika Pandegiling, Surabaya
• Hotel Fave Pasar baru Jakarta, Jakarta
• Hotel Ibis Solo
• Hotel Ibis Simpang Lima, Semarang
• Hotel Ibis Malioboro, Yogyakarta

Mobile : (081215875419 / 085643156780)

Email : seminarcenterindonesia@gmail.com / indotciproconsultant@gmail.com

Web: jadwalinformasitraining.com

Catatan :

• Pelatihan ini dapat di-customized sesuai kebutuhan perusahaan Anda bila diselenggarakan dalam bentuk In-House Training. Untuk permintaan In-House Training dengan jenis topik lainya, silahkan mengirimkan ke alamat email yang tercantum di web kami.
• Request Training. Jika anda membutuhkan informasi pelatihan yang belum tercantum pada website ini, atau anda ingin memberikan usulan materi yang sesuai dengan tingkat kebutuhan perusahaan anda, silahkan mengirimkan ke alamat email yang tercantum.
• Bila tidak ada tanggal dan waktu atau yang tercantum sudah kadaluarsa didalam artikel mohon tanyakan kepada kami untuk jadwal terbarunya.
• Peserta bisa mengajukan Tanggal Pelatihan / Training selain yang tertera pada silabus penawaran