Training Electrical Equipment & Control Systems: Commissioning, Testing & Start-Up of Electrical Systems

Kami menerima request waktu, tempat & fasilitas hubungi kami untuk informasi lebih lanjut.

Training Electrical Equipment & Control Systems: Commissioning, Testing & Start-Up of Electrical Systems

Introduction

The safe and efficient operation of modern electrical equipment and control systems requires the successful testing, start-up and commissioning of this equipment, or system, to ensure correct operation, plus;

• Accurate troubleshooting
• Subsequent repair of this equipment, or system
• Ensuring continued productivity

Delegates are encouraged to bring with them any technical issues that they may wish to discuss during the seminar.

Seminar Objectives

On successful completion of this seminar, participants will have:

• A better understanding of commissioning procedures
• A better understanding of troubleshooting procedures
• An improved capability in the use of test equipment
• A better understanding of failure modes and failure analysis
• A refreshed awareness of electrical safety concerns

Training Methodology

Each seminar participant will receive a copy of the comprehensive course notes. The presenter will outline and discuss the topics using ‘power point’ and others. The course is designed to have an interactive format to maximize delegate participation. Questions and answers are encouraged throughout and at the daily work sessions. Needs-Based case-studies and examples will be discussed in problem solving workshop sessions. Only minimum note taking is encouraged to ensure maximum delegate attention during the course.

Organisational Impact

On successful completion delegates will have:

• Developed a structured approach to electrical commissioning, testing and troubleshooting
• Been given methods/solutions for various electrical problems
• Interacted and gained from shared experiences
• Examples and case studies to illustrate the material being discussed
• Technical material appropriate to the organisations represented

Personal Impact

On successful completion of this course delegates will be able to:

• Use test equipment for electrical commissioning and servicing
• Better understand the design, functionality and failure modes of electrical equipment and control systems
• Utilize single-line diagrams and schematics for troubleshooting
• Understand standard work practices plus be able to develop job plans, which assist in successful commissioning and troubleshooting
• Show a refreshed knowledge of electrical safety

Who Should Attend?

• Electrical Engineers
• Electrical Supervisors
• All Electrical Professionals commissioning, testing, start-up, troubleshooting, maintenance and repair of ‘Electrical Equipment’ and ‘Control Systems’. Because the methods and examples are generic, personnel from all industries will benefit. Participants need no specific requirements other than good understanding of electricity and some relevant experience.

Programme Outline

The Technology of Electrical Equipment Transformers – Power supplies (UPS) – Batteries Generators – Switchgear – Disconnect switches Neutral ground resistors (NGR) Motor control centers (MCC) – Variable frequency/speed drives (VFD/VSD) Programmable logic controllers (PLC) – Distributed control systems (DCS) Power monitoring Control relays/timers/switches – Motor/feeder protective devices Miscellaneous equipment – Heaters, solenoid valves, electric valve actuators and signalling/alarm devices

Commissioning and Testing of Electrical Equipment Methods Principles – Special techniques NEC check lists Troubleshooting of Electrical Equipment Methods – Terminology – Principles Special techniques Case studies/examples Single line drawings Group exercises

The Use of Test Equipment Digital voltmeter (DVM) Megger Frequency meter Temperature probes/pyrometers Ammeters, Power meters Load banks Digital hydrometers Cable fault locators

The Interpretation and Use of Drawings Single-line electrical drawings Control schematics Wiring lists P&ID’s Logic and standard symbols The Development of a Job Plan Identification of the troubleshooting step-by-step sequence Procedure preparation Follow-up Safety considerations and training

The Identification and Repair of Problems/Failures Common mode failures,Phase imbalance Electronic component failure, Fusing Fusing Motor windings/bearings/brushes Excitation circuits Battery cells, Inverters/rectifiers Inverters/rectifiers Bushings – Switches Control circuits Ground faults A review of Safety Requirements Area classifications NEC electrical codes, Safety Information Open session:Case Studies, Questions and Answers

Instruktur

Dr. Ir. Viktor Malau DEA. (Associate Professor) dan Team

• Doctor, Genie des Materiaux, Ecole Centrale de Lyon, France, France, September 1994 – September 1996
• Master, Genie des Materiaux, Ecole Centrale de Lyon, France, France, September 1992 – October 1993
• Undergraduate, Mechanical Engineering, Gadjah Mada University, Indonesia, August 1978 – April 1985

Tugino ST. MT

FASILITY

Quality training material (hardcopy and softcopy), Quality training kits: bag, block note, ballpoint,  including jacket or T-shirt, Flashdisk 8 Gb, Dinner, City Tour (Yogyakarta and Bandung) etc,  Convenient training facilities in 3,4,5 stars hotel, Lunch per day, morning and afternoon coffee / tea breaks for along the training,Certificate&Photo.

————————————————————————————————————————————————————————————————

Mobile : (081215875419 / 085643156780)

Email : seminarcenterindonesia@gmail.com / indotciproconsultant@gmail.com

Web: jadwalinformasitraining.com

Catatan :

• Pelatihan ini dapat di-customized sesuai kebutuhan perusahaan Anda bila diselenggarakan dalam bentuk In-House Training. Untuk permintaan In-House Training dengan jenis topik lainya, silahkan mengirimkan ke alamat email yang tercantum di web kami.
• Request Training. Jika anda membutuhkan informasi pelatihan yang belum tercantum pada website ini, atau anda ingin memberikan usulan materi yang sesuai dengan tingkat kebutuhan perusahaan anda, silahkan mengirimkan ke alamat email yang tercantum. Register Disini
  
• Bila tidak ada tanggal dan waktu atau yang tercantum sudah kadaluarsa didalam artikel mohon tanyakan kepada kami untuk jadwal terbarunya.
• Peserta bisa mengajukan Tanggal Pelatihan / Training selain yang tertera pada silabus penawaran