TRAINING ELECTRICAL POWER SYSTEM ANALYSIS

TRAINING ELECTRICAL POWER SYSTEM ANALYSIS

OBJECTIVE

By Join This Program, Participant Will :

• Power System Analysis means verifying the adequacy of the power distribution system and it’s components.
• Recognize coordination related disturbances and outages.
• Collect the required data to perform a detailed coordination study.
• Derive complete protective device settings for some of the simpler electrical power systems that are consistent with NEC requirements.

TARGET AUDIENCE

This course is intended for anyone who must perform calculations, provide settings or approve the work performed by others. The trainee should be a graduate engineer or have the equivalent practical work experience in electrical power systems.

OUTLINE

1. Introduction to Industrial Power Systems

Single-Phase Power Loads

Three-Phase Power Loads

Substation Configurations

1. Short Circuit Theory and Terminology

Effects of Short Circuits

Fault Current Sources

Machine Reactances

Fault Current Characteristics

1. Electrical Equipment Ratings

Fuses

Circuit Breakers

Motor Starters

Conductors and Bus

1. Balanced Fault Calculations

Per-Unit Modeling

Data Collection

Impedance Calculations

Momentary and Interrupting

Duty Calculations

1. Coordination Fundamentals

Procedures

Data Collection

Scaling Factors

1. Plotting Time/Current Curves

Circuit Breakers

Fuses

Time Delay/Instantaneous Relays

Relay Coordination Intervals

1. Equipment Protection and Coordination

NEC and ANSI/IEEE Criteria

Conductors (Low and Medium Voltage)

Transformers

Motors e. Conductors (Low and Medium

INSTRUKT0R & CV

• Tugino, ST, MT/ Team
• He graduated Master of Electrical Engineering (S2) UGM 2003. He Practitioner field of electricity. His Experiences Instructor Training Certification Become K3 Electricity, Instructor PUDIKLAT / PUSDIKLAT PLN, Power Transformer, Programmable Logic Controllers, Control Valve and Instrumentation, Emergency Generator Systems, Renewable Energy, Distributed Control sysytem, Electrical Inspection Tool Pressure Relief Valve, Process Safety, Distributed Control System (DCS) and Supervisory Control and data Acquisition (SCADA), Pneumatic Tool, Operation, Maintenace and Repair, Gas Engine Operation and Maintenance, Electrical Safety, Basic Electricity Instrument Process Control, Electric Motor Control, Programmable Logic, Design and application of robots, Process Control Instrumentation, Programming and application of PLC, Harmonics in Power Systems (causes and prevention, Installation Planning Information and Computer Interfacing Power Electronics Power, Power Distribution, Preventive and Predictive Maintenance Pump and Valve, Audit and Management Electrical Energy, Diesel Engine Operation and maintenance, Electrical Submersible Pump and Centrifugal Pump, Electrical Safety.

TRAINING METHOD

1. Presentation
2. Discussion
3. Case Study
4. Evaluation 

_____________________________________________________________________________________________________________________

Kami memberikan alternatif Fasilitas atas Investasi anda dalam Program ini, diantaranya :

1. Sertifikat, Peralatan Training, USB, Souvenir, Lunch, Coffe Break, City Tour
2. Running minimal 2 Orang (Semarang, Jogja, Solo), Running minimal 3 Orang (Bandung, Jakarta), Running 4 Orang diperuntukan untuk daerah (Bali, Lombok, Manado, Balikpapan)
3. Kami menyediakan transportasi antar Jemput dari Stasiun/Bandara ke Tempat Pelatihan(Hotel) bagi perusahaan yang Running minim 2 Orang
4. Harga dilampirkan di Brosur Penawaran

______________________________________________________________________________________________________________________

Tambahan Informasi :

1. Silahkan tanyakan ketersediaan Tanggal dan Waktu dari jadwal training terbaru apabila anda tidak menemukan waktu yang sesuai dengan jadwal anda.

2. Training dapat disesuaikan dengan kebutuhan perusahaan jika dalam bentuk In-House Training. Silahkan baca ketentuan In-House Training diwebsite kami atau hubungi kami di Nomer Mobile untuk mendapatkan Fast Respon.

3. Silahkan mengisi Form Request Training di website kami untuk mendapatkan informasi tambahan yang belum ada, atau jika anda ingin menanyakan usulan materi sesuai kebutuhan perusahaan. Hubungi kami lewat email yang tertera atau Register disini!

4. Apabila telah menerima Silabus Training, Customer dapat Request Waktu Training yang diinginkan.

5. Informasi dan Data yang jelas akan memudahkan kami untuk segera merespon permintaan anda.

Customer Dapat Request Tempat, Waktu, serta Fasilitas Training. Silahkan Hubungi kami untuk Menerima Brosur Penawaran.