Advanced Rigging For Supervisor

COURSE OBJECTIVES

At the end of course, the participant should be able to:

• Observe general safety first rules and carry out his duties in a safe
  and responsible manner.
• Have knowledge of safe working load of the crane he is working with.
• Have a full knowledge of hand signal (Australian/New Zealand Standard)
• Understand the correct type of sling, hook shackle etc. for load.
• Have knowledge of the use of lifting beams, slings and chains.
• Understand the effect of doubling crane hoist rope on safe working.
• Understand use of rope, chain and shackle.
• Understand not to use damaged wire rope or fiber rope, slings or chain where the links are not free or kinked wire rope.
• Understand when slinging a load, pack between sling and load at all point where load has sharp corners, so as to prevent damage to sling.
• Design and apply the knowledge of lifting and lifting plan in their daily work

COURSE OUTLINE

Day 1:

Introduction:
Definition of Dogger, Slinging & Crane Operator

Roles & Responsibilities of Rigger

• Roles & responsibility of Crane Operator
• Roles & Responsibility of Dogger
• Roles & Responsibility of Slinger
• Roles & Responsibility of Traffic Controller / Flagman
• Roles & Responsibility of Lifting Supervisor
• Accident & Prevention

Legislative Requirement

• International Standard: AS/NZS
• Roles and Responsibilities :Crane operator, Crane Owner/End User, Facility/Site Owner,

Lift Coordination, Lift Engineer/Rigging Specialist, Workers and Crane Mechanic
Hazard And General Safety

• Outriggers and Crane Stability
• Comparative Soil Bearing Capacities
• Crane Selection Guide
• Electrical Hazard
• Public Road / Pedestrian Hazards
• Utilities Overhead and underground
• Accidents and Lesson learn

Signalling And Communication

• Two way Radios
• Conventional Radio
• Trunked Radio
• Radio Direction for Crane Driver
• Bell or Whistle Code
• Hand Signal

Day 2

Rigging Engineering Calculation

• Determination on Centre of Gravity
  Rectangular Object
  Round or Oval Shape
  Multiple Load / Object
• Rigging Engineering Calculation (2) (b) Volume Calculation
  Rectangular Object
  Round or Oval Shape
  Triangle Object
  Cone Object
  Multiple Load / Object
• Ropes & Knots for Rigger (Synthetic & Natural)
  Figure of Eight
  Reef knot
  Single Bowline
  End Splice
  Eye Splice
  Sheet Bend
  Timber Hitch
  Rolling Hitch
  2 and Half Hitch
  Tagline Hitch
  Clove Hitch
• Rigging Engineering Calculation (3)
  Calculation of Mass
  Basic Mass Calculation for Various Shapes of Loads Normally Engaged During Crane
  Operation versus volume
  Concrete / Cement
  Steel (Mild / Hard
  Liquid (Water)
  Wood
  Sand
  ** Guidelines for Steel pipe, steel bar, Angle Bar, Mild Steel Plate, Mild steel plate bar, C-Channel, Universal Beams, Universal Columns, etc
  Lifting Appliances
  Selection on Sling material
• Sling wire FSWR 1570
• Sling wire FSWR 1770
• Chain Sling GT80 / G100
• Synthetic Webbing (Flat/Round Slings)

Stacking and Clearances

• Clearance
• Stacking Steel Plate
• Stacking Rolled Steel Coils And Other Round Loads
• Stacking Timber

Care, Maintenance, and Inspection on Sling Material
Spreader Bar vs Stabilizer Bar
Use of Slings / Hoists And Tag line
Determination of S.W.L (SWL versus WLL)
Minimum Breaking Force (MBF) and its usages

Day 3

• Rigging Engineering Calculation (4)

Safety Factor Requirements Lifting Material & Human
(a) Sling wire FSWR 1570
(b) Sling wire FSWR 1770
(c) Chain Sling GT80 / G100
(d) Synthetic Webbing (Flat/Round Slings)
(e) ‘choke’ / Hitch Factor

• Rectangular Load
• Round Load

(f) Sling Angles Factor

• Sudut 30^o
• Sudut 45^o
• Sudut 60^o
• Sudut 90^o
• Sudut 120^o
• Determination of sling Strength based on diameter & Safety Factor
• Sling Wire
• Synthetic Sling
• Chain Sling
• Determination of Sling length and lifting angle

 

Day 4

• Rigging Engineering Calculation (5)

Inspection of Slings & shackles and attachments

• Sling Wire (5%)
• Chain Sling (5%)
• Synthetic Sling

Note: Determination of acceptance condition of slings and attachments. (Category 1 and Category 2)

• Rigging Engineering Calculation (6)
• Calculation of Multiple Sling

SWLSling 1

SWL Sling 2

• Multiple Crane Lifting / Multiple @ Large Loads(e) Tendem Lifting

Crane Selection and Ordering crane

• Crane type vs Load Chart & Working Radius

1. Mobile Crane
2. Crawler Crane

 

INSTRUKTOR & CV

 

Ir. Setyawan Hardan, M.Sc/ Team

Topics For Instructors

1. Mechanical Engineering.

• MaintenanceManagement/Maintenance Management
• Maintenance ofplant
• Failure Analysis
• MeasurementFundamentals
• WeightManagementTools
• Pump&Compressor
• GasTurbine
• Steam Turbines
• Piping
• GasEngine
• Boiler
• DieselEngine
• CombustionProcess
• Welding
• Metallurgy&MetalTesting
• includingDestructiveTest(DT &) andNon DestructiveTest(NDT)
• Rigging
• Metrology
• CraneOperation&Maintenance

______________________________________________________________________________________________________________________

Kami memberikan alternatif Fasilitas atas Investasi anda dalam Program ini, diantaranya :

1. Sertifikat, Peralatan Training, USB, Souvenir, Lunch, Coffe Break, City Tour
2. Running minimal 2 Orang (Semarang, Jogja, Solo), Running minimal 3 Orang (Bandung, Jakarta), Running 4 Orang diperuntukan untuk daerah (Bali, Lombok, Manado, Balikpapan)
3. Kami menyediakan transportasi antar Jemput dari Stasiun/Bandara ke Tempat Pelatihan(Hotel) bagi perusahaan yang Running minim 2 Orang
4. Harga dilampirkan di Brosur Penawaran

______________________________________________________________________________________________________________________

Tambahan Informasi :

1. Silahkan tanyakan ketersediaan Tanggal dan Waktu dari jadwal training terbaru apabila anda tidak menemukan waktu yang sesuai dengan jadwal anda.

2. Training dapat disesuaikan dengan kebutuhan perusahaan jika dalam bentuk In-House Training. Silahkan baca ketentuan In-House Training diwebsite kami atau hubungi kami di Nomer Mobile untuk mendapatkan Fast Respon.

3. Silahkan mengisi Form Request Training di website kami untuk mendapatkan informasi tambahan yang belum ada, atau jika anda ingin menanyakan usulan materi sesuai kebutuhan perusahaan. Hubungi kami lewat email yang tertera atau Register disini!

4. Apabila telah menerima Silabus Training, Customer dapat Request Waktu Training yang diinginkan.

5. Informasi dan Data yang jelas akan memudahkan kami untuk segera merespon permintaan anda.

Customer Dapat Request Tempat, Waktu, serta Fasilitas Training. Silahkan Hubungi kami untuk Menerima Brosur Penawaran.